{"id":1417,"date":"2018-11-26T06:21:26","date_gmt":"2018-11-26T06:21:26","guid":{"rendered":"https:\/\/www.agriculture-machine.com\/?p=1417"},"modified":"2023-05-12T14:29:22","modified_gmt":"2023-05-12T06:29:22","slug":"common-repair-and-replacement-points-for-corn-grinder","status":"publish","type":"info","link":"https:\/\/www.agriculture-machine.com\/de\/common-repair-and-replacement-points-for-corn-grinder\/","title":{"rendered":"H\u00e4ufige Reparatur- und Austauschpunkte f\u00fcr die Maismahlmaschine"},"content":{"rendered":"
\n \n
\n \n
\n
\n \n\n
<\/div>\n <\/div>\n
\n \n\n
<\/div>\n <\/div>\n
\n \n\n
<\/div>\n <\/div>\n
\n \n\n
<\/div>\n <\/div>\n
\n \n\n
<\/div>\n <\/div>\n <\/div>\n \n
\n
\n \n\n
<\/div>\n <\/div>\n
\n \n\n
<\/div>\n <\/div>\n
\n \n\n
<\/div>\n <\/div>\n
\n \n\n
<\/div>\n <\/div>\n
\n \n\n
<\/div>\n <\/div>\n <\/div>\n<\/div>\n \n\n
\n 4,5\/5 - (26 Stimmen) <\/div>\n <\/div>\n

1. Reparatur und Austausch des Siebs. Das Sieb besteht aus Blechstahl oder perforiertem Eisen. Wenn das Sieb abgenutzt oder durch Fremdk\u00f6rper besch\u00e4digt ist, wenn der Schaden nicht gro\u00df ist, kann es durch Nieten oder L\u00f6ten repariert werden; wenn der Bereich besch\u00e4digt ist, sollte das neue Sieb ersetzt werden. Beim Einbau des Siebs sollte die Gratseite des Siebs nach innen zeigen, die gl\u00e4nzende Seite nach au\u00dfen, und das Sieb und der Siebrahmen sollten fest anliegen. Wenn das Ringsieb installiert wird, sollte die \u00dcberlappung in Richtung der Rotation zeigen, um zu verhindern, dass das Material an der \u00dcberlappung stecken bleibt.<\/p>\n

<\/a><\/a><\/p>\n

Second, the lubrication and replacement of the bearings. The Maismahlmaschine<\/strong><\/a> is cleaned after every 300 hours of operation. If the bearing is oil lubricated, it is advisable to fill the bearing housing clearance by 1\/3 when adding new oil, and the maximum is not more than 1\/2. Just tighten the capped oil cup cover a little before operation. When the Maismahlmaschine<\/strong><\/a> bearing is seriously worn or damaged, it should be replaced in time, and pay attention to strengthen lubrication; if using tapered roller bearing, pay attention to check the axial spacing of the bearing to keep it 0.2-0.4 mm. If there is discomfort, increase it. Reduce the paper pad at the bearing cover to adjust.<\/p>\n

Third, the replacement of the claws and hammers. Among the pulverizing parts, the pulverizing claws and the hammer pieces are the wearing parts in the Maismahlmaschine<\/strong><\/a>, and are also the main components affecting the pulverizing quality and productivity. The pulverizing claws and the hammer pieces should be replaced in time after being worn. When the jaw crusher replaces the claws, the disc should be pulled out first. Before pulling out, first open the round nut lock piece on the back of the disc, use a hook wrench to unscrew the round nut, and then pull the disc out with a special puller. In order to ensure the balance of the rotor operation, it is necessary to pay attention to the complete set of replacement when changing the teeth. After the replacement, static balance test should be done to make the Maismahlmaschine<\/strong><\/a> work stable. Be sure to tighten the nut when assembling the jaws, and be careful not to miss the spring washer. The qualified parts should be selected when changing the teeth. The weight difference of the single teeth should be no more than 1.0-1.5 grams.<\/p>","protected":false},"excerpt":{"rendered":"

1. Repair and replacement of the screen. The screen is made of sheet steel or iron perforated. When the screen is worn or broken by foreign matter, if the damage is not large, it can be repaired by riveting or soldering; if the area is damaged, the new screen should be replaced. When installing the […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"template":"","tags":[51,52],"info-type":[21],"class_list":["post-1417","info","type-info","status-publish","hentry","tag-corn-grinder","tag-corn-grinder-machine","info-type-news"],"_links":{"self":[{"href":"https:\/\/www.agriculture-machine.com\/de\/wp-json\/wp\/v2\/info\/1417","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.agriculture-machine.com\/de\/wp-json\/wp\/v2\/info"}],"about":[{"href":"https:\/\/www.agriculture-machine.com\/de\/wp-json\/wp\/v2\/types\/info"}],"author":[{"embeddable":true,"href":"https:\/\/www.agriculture-machine.com\/de\/wp-json\/wp\/v2\/users\/1"}],"wp:attachment":[{"href":"https:\/\/www.agriculture-machine.com\/de\/wp-json\/wp\/v2\/media?parent=1417"}],"wp:term":[{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.agriculture-machine.com\/de\/wp-json\/wp\/v2\/tags?post=1417"},{"taxonomy":"info-type","embeddable":true,"href":"https:\/\/www.agriculture-machine.com\/de\/wp-json\/wp\/v2\/info-type?post=1417"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}